maker:listofsoftwareformakers
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
maker:listofsoftwareformakers [2014/05/27 01:32] Anibit |
maker:listofsoftwareformakers [2015/05/24 07:25] (current) Anibit [HeeksCNC] |
||
|---|---|---|---|
| Line 17: | Line 17: | ||
| ==== SciTe ==== | ==== SciTe ==== | ||
| - | {{page>maker:reviews:7_zip&nodate&nouser&noheader&indent&firstseconly&nocomments}} | + | {{page>maker:reviews:scite&nodate&nouser&noheader&indent&firstseconly&nocomments}} |
| http://www.scintilla.org/SciTE.html | http://www.scintilla.org/SciTE.html | ||
| Line 28: | Line 28: | ||
| {{page>maker:reviews:7_zip&nodate&nouser&noheader&indent&firstseconly&nocomments}} | {{page>maker:reviews:7_zip&nodate&nouser&noheader&indent&firstseconly&nocomments}} | ||
| - | http://www.7-zip.org/ | ||
| - | |||
| - | {{:windows.jpg}} | ||
| ==== Hex Edit ==== | ==== Hex Edit ==== | ||
| Line 46: | Line 43: | ||
| {{page>maker:reviews:thegimp&nodate&nouser&noheader&indent&firstseconly&nocomments}} | {{page>maker:reviews:thegimp&nodate&nouser&noheader&indent&firstseconly&nocomments}} | ||
| - | http://www.gimp.org/ | ||
| - | |||
| - | {{:windows.jpg}} {{:linux.jpg}} {{:osx.jpg}} | ||
| ==== Inkscape ==== | ==== Inkscape ==== | ||
| Line 54: | Line 48: | ||
| {{page>maker:reviews:inkscape&nodate&nouser&noheader&indent&firstseconly&nocomments}} | {{page>maker:reviews:inkscape&nodate&nouser&noheader&indent&firstseconly&nocomments}} | ||
| - | http://www.inkscape.org/ | ||
| - | |||
| - | {{:windows.jpg}} {{:linux.jpg}} {{:osx.jpg}} | ||
| ==== Paint.Net ==== | ==== Paint.Net ==== | ||
| Line 103: | Line 94: | ||
| {{page>maker:reviews:freecad&nodate&nouser&noheader&indent&firstseconly&nocomments}} | {{page>maker:reviews:freecad&nodate&nouser&noheader&indent&firstseconly&nocomments}} | ||
| - | |||
| - | http://freecadweb.org/ | ||
| - | |||
| - | {{:windows.jpg}} {{:linux.jpg}} {{:osx.jpg}} | ||
| ===== CAM ===== | ===== CAM ===== | ||
| Line 114: | Line 101: | ||
| {{page>maker:reviews:heekscnc&nodate&nouser&noheader&indent&firstseconly&nocomments}} | {{page>maker:reviews:heekscnc&nodate&nouser&noheader&indent&firstseconly&nocomments}} | ||
| - | http://heekscnc.blogspot.com/2014/03/heekscnc-10.html | + | http://heekscnc.blogspot.com/2014/03/heekscnc-10.html ((You can buy the Windows binary, or build it yourself. HeeksCNC is a nice piece of software, please consider purchasing it.)) |
| - | {{:windows.jpg}} | + | {{:windows.jpg}} {{:linux.jpg}} |
| ==== OpenScad ==== | ==== OpenScad ==== | ||
maker/listofsoftwareformakers.1401154365.txt.gz ยท Last modified: 2014/05/27 01:32 by Anibit
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
